Accessibility Widget: On | Off
btn
btn
25 of 33
Create New Tag
C-LION C-LION
5/14/2020 5:26 AM
dmcd38 wrote:

new sender in July smile

Any evidence for this statement? Can‘t wait... 😛

| Quote
garretttollette garretttollette
5/20/2020 10:44 AM

new prototype vee tire seen on brannigans bike Photo

| Quote
bturman bturman
5/20/2020 2:20 PM

New shoes in the wild?! Fabio Wibmer looking fresh:

Like bikes? Hit Vital up on Instagram, Facebook, and YouTube.

| Quote
bturman bturman
5/20/2020 2:43 PM

Jerome Clementz hinting at a new Cannondale dropping tomorrow:

Like bikes? Hit Vital up on Instagram, Facebook, and YouTube.

| Quote
garretttollette garretttollette
5/20/2020 3:16 PM

it also looks like maxxis has a slightly updated shorty/mid-spike. seen on blekinsops dh rig at crankworks and Brendans e-bike in his latest vid. Photo
Photo

| Quote
watchcwgo watchcwgo
5/20/2020 6:52 PM

Vee assegai looks good

| Quote
Shawn_Trudell Shawn_Trudell
5/20/2020 8:34 PM

Theres also a very grainy picture of it in Jordie's bike check on the "Fox Dialed" series.

Jodie even mentions in the comments that its NOT a shorty replacement. Perhaps a new Wet Scream.

| Quote
Shawn_Trudell Shawn_Trudell
5/20/2020 8:35 PM
Photo
Photo
| Quote
Shawn_Trudell Shawn_Trudell
5/20/2020 8:38 PM
watchcwgo wrote:

Vee assegai looks good

I haven't figured out why Vee make a maxxis knock off and then installs the cornering knobs backwards? I always understood part of the reason maxxis tires braked so well was the L shape of the corner knob. But what do I know.

| Quote
manhattanprjkt83 manhattanprjkt83
5/22/2020 7:20 AM

Really love the look of that maxxis, i used to run the medusa back in the day and loved that tire for we weather...similar lines:

Photo

| Quote
garretttollette garretttollette
5/22/2020 3:21 PM

I noticed this hack that cathro did to prevent Shimano brake pad rattle, has anyone else ever done this? Marshy maybe? Does anyone have any more examples?
| Quote
garretttollette garretttollette
5/22/2020 3:22 PM
Photo
here is the photo
| Quote
Scrub Scrub
5/22/2020 3:40 PM
garretttollette wrote:
I noticed this hack that ...more

Yeah back in '09 on some Juicy 7's I put some mastic tape on the metal brake caliper clip to stop the rattle. You would think manufacturers would have had an over engineerer solve this issue long ago, unnecessary noise. whistling

| Quote
sspomer sspomer
5/22/2020 5:15 PM
| Quote
Broken_spoke.photo Broken_spoke.photo
5/22/2020 5:51 PM

With all these shimano hacks for the saint calipers, Shouldn't shimano listen and update the already ancient saint groupset? Id totally run a saint 12 speed on my enduro bike if it was bullet proof like the old DH set.

Snoopin around lookin for the best trails and sketchiest lines

| Quote
Maxipedia Maxipedia
5/22/2020 11:41 PM
Broken_spoke.photo wrote:

With all these shimano ...more

Don't you believe Shimano know this and are already in the works with this since probably a few years now?

No to mention the fact that Saint is already pretty old and still relevant. Shifter and derailleur are okay (it's a DH bike grouppo, you don't shift around that much anyway), Shimano cranks are better than SRAM regardless how you look at them, they are just hassle-free, and the brakes have been a good standard for a small eternity, with the competition catching on in more recent years. But let's not forget what we had before!

I'd like to mention that I like SRAM more than Shimano, as a company, and run a X.0 drivetrain with Saint M820 brakes on my DH bike. Before that was in full SRAM mode and almost killed myself when my fresh bled Codes (the second generation) with just bed-in pads just stopped working simultaneously in a high speed corner of a practice run at a race. I was instantly teleported into a tree and it luckily resulted only in a huge lateral bruise that you more than sure wouldn't like to see.I know SRAM/Avid brakes have come quite a way since then, but I still don't feel too positive about them, due to the above.

Mx

| Quote
Jrp Jrp
5/26/2020 2:23 AM

Looks like the DVO boys have the new shock ready to ride

Photo

| Quote
piroloco piroloco
5/27/2020 3:33 PM

Florian Nicolai and his new RS Fork (ZEB?)
Photo

| Quote
vweb vweb
5/28/2020 12:30 AM
piroloco wrote:

Florian Nicolai and his ...more

In this angle it doesn't appear to be larger stanchions... Burlier crown for sure, but from this point of view, that's it.

| Quote
baronKanon baronKanon
5/28/2020 1:18 AM

If you look at an earlier post from Flyinflo21, you get a closeup of the crown. Looks burlier for sure with larger interface with the stanctions than lyrik (eyeballing it). From the pic above, it also seems that the lowers go a bit below the axle, as the longer insert of the stanctions makes the stanctions go further down. I think this is one step further in the right direction.

Also, when listening to the the Chris Porter interview on Bikeradar podcast, he mentions that one drawback of current forks is that the bushings are fixed in the outers, whereas on motor sports forks, there is one on the stanction as well which increases the bushing distance when you are far into the travel, meaing that when there is a lot of force on the fork, the bushings keep things better in place and lessens bushing binding. I think this may hint something about the EXT Era fork, which I bet he have had something to say about with Mojo Risin's close collaboration with EXT. CRConception already have floating bushings on their upside down forks (cannot embed photo, follow the link). http://www.crconception.com/FORE-SC/

| Quote
Primoz Primoz
5/28/2020 1:53 AM

I actually deal a bit with similar (albeit much smaller) bushings at work. While there are external bushings available on the market, they are few and far inbetween. With a hole, reamed to the correct size, you can achieve quite good tolerances on the final bushing hole by squeezing it together, closed and reaching the desired diameter, all the while having a snug press fit. With an external bushing you'd have to have a gap in it and make it larger in order to have a snug fit, where it wouldn't move. And there's your problem then, you have a gap. Unless you control that gap by placing it on the side (along the wheel axis), you're going to have a bad time.

I'd really like to see how this MX bushings are dealt with, but yeah, can't be easy to make them fit.

Plus, if you have a sliding surface for an internal bushing (at the top of the lowers) and then another external bushing fitted to it at the end, how do you pull the fork apart? With a dismantable fork (upside down and a removable axle nut/mount, for example) you could pull it out from the top. There are other solutions of course (removing it together with the leg), but then there's a question of assemblybility, can the process be good in mass production, how finnicky is it to service, etc. At the end of the day what we have works reasonably well or well enough for most people not to give a damn. And those people won't pay x2 or x3 the price for a fork to get a marginal gain. And until DH isn't running custom products along these lines, I don't think it can be called 'the F1 of MTB'. Everything is too close to stock to be F1.

| Quote
baronKanon baronKanon
5/28/2020 2:02 AM
Primoz wrote:

I actually deal a bit with ...more

This I think requires high precision machined outer tubes, which is not that feasible on the cast magnesium lowers everybody use. Also it would require a removable sleeve to get the floating bushing out. The Reverb works like that. One inner and one outer, where the outer bushing is in the big nut sleeve on the top of the outer and the other is on the inner tube. Hands up everybody who have destroyed the inner bushing trying to install after a service on the Reverb? smile

| Quote
Primoz Primoz
5/28/2020 2:31 AM

Yeah, I forgot that part as well, thanks for reminding me. As for reverb servicing I'm 1 for 1 in the success camp, no destroyed bushings.

| Quote
David9180 David9180
5/28/2020 3:59 AM
piroloco wrote:

Florian Nicolai and his ...more

vweb wrote:

In this angle it doesn't ...more

Sam Hill´s bike

Photo
Photo

Shred some trail!!!

| Quote
mitch160 mitch160
5/29/2020 6:09 PM

New Forbidden Bike being released next week Photo

| Quote
brash brash
5/29/2020 7:06 PM

I should have held out if that's a 150/160 29'er high idle. But this META AM29 is absolutely sick and the frame was dirt cheap. Very impressed with the croissant mobile.

| Quote
shreda shreda
5/30/2020 12:13 AM
mitch160 wrote:

New Forbidden Bike being ...more

Same bike, new colors is my guess

| Quote
nathan999x nathan999x
5/30/2020 6:12 AM
shreda wrote:

Same bike, new colors is ...more

I think Lewis Buchanan was hinting at a longer travel bike which would make sense. It seems weird to run a 130mm travel bike for the ews.

| Quote
Mandingo915 Mandingo915
5/30/2020 8:01 AM
mitch160 wrote:

New Forbidden Bike being ...more

shreda wrote:

Same bike, new colors is ...more

nathan999x wrote:

I think Lewis Buchanan was ...more

You’re both probably right. Probably same bike new linkage to increase travel

| Quote
Sean_Hornchek Sean_Hornchek
5/30/2020 10:34 AM
shreda wrote:

Same bike, new colors is ...more

nathan999x wrote:

I think Lewis Buchanan was ...more

Mandingo915 wrote:

You’re both probably ...more

I really hope its a new link and colors, only thing I wished my druid had is 10-20mm more travel.

| Quote
25 of 33

Post a Reply

Cool Wink Smile Tongue Laughing Shocked Sick Angry Blink Sad Unsure Kissing Woohoo Grinning Silly Pinch Sideways Whistling Evil Dizzy Blush Cheerful Huh Dry